REPLACING ALUMINUM WINDOWS WITH VINYL RETROFIT WINDOWS OR REPLACEMENT STYLE WINDOWS

In previous articles, I explained to you how to determine either your windows are candidates for vinyl replacement style frames or retrofit style frames. This week I'm going to explain its installation techniques for both frame styles. Let's start with the retrofit frame.

Retrofit window installation is definitely the easiest of all. The retrofit window even now comes with an exterior consistent attached. That's the flush fin that goes against the outside surface, usually stucco. Prepare the window by drilling 3/8" holes in the areas of the frame where you want to screw tangible in place. Normally, there will be 3 holes on each side and 3 more across its top. Don't predrill each holes in the base track. After removing the hackneyed panels, you want to run a heavy bead of caulk on the guise of the old aluminum frame that you disappeared grease place. then you and a supporter set the bottom of the vinyl window onto the old aluminum bottom course also raise it into position. The flush fin or retrofit lip will act as a "stop" to hold the window in place. understand your helper hold the window while we go inside.

Once inside, you want to center the window moment the opening. declination the vent panel open and closed to make sure the window is plumb again level. To adjust for peripheral of claim conditions, shim the bottom pertinent or left corner by placing a shimming collateral between the sill and bottom of the window frame. Once square, drive a 3" rug screw whereas the 3/8" holes and into the wood studs.Just seat the screw, don't overtighten. after you get the screws into its sides also top, disrobe its sliding panel. The bottom track should lift out. Look for drainage holes in the track and attach a thin screwdriver besides lift up. Drive apart screw in the bottom center, caulk around its screw head, then stabilize the track back in moor and re-install the sliding panel. Now, you want to go behind outside and caulk the gap where the retrofit breakwater meets the exterior surface of the house. You want to have a double barrier of protection opposite water infiltration. Remember, you up-to-date applied a generous bead of caulk before inserting the new frame into the opening. The rest of the job is done on the inside.

First, you want to capsule the 3/8" screw holes to hide the horde of the screws. We sell the hole plugs on the website. Just click on the "Purchase Trim" tab to see a adumbrate. The plugs will pop into place in the hole. The next hike is to fill the gap around the new frame with R-13 Insulation. Do not use the foam insulation that comes in the can. Many manufacturers will not honor the guaranty if the foam is used. Even the non expanding foams authority cause the frame to distort, causing difficulties. transfer its insulation in tight. You dexterity want to lazy a dust mask at this procedure. Many people, myself included, are very allergic to insulation. After the insulation is in place, you want to install rolled around the inside to finish its job. You can use wood trim from the hardware store, or some discrepant product. But in my experience, the best product is a vinyl stupid trim that matches its window frame. The flat trim importance also be purchased on the website under the "Purchase Trim" tab, or you could tryout to find it from a local window contractor. Ours comes in 2 different widths, although the 1 3/4" wide piece is by far the most common. The trim has a double sided adhesive tape on the back. You blemish the top and bottom first, stick them on the vinyl frame, making sure its trim goes to the drywall. This covers all the insulation and the old steel frame. Do the element bits next. The final step is to caulk where the trim meets the walls.

Much of the starting point process for the replacement frame is the same as the retrofit frame. But, qualified are a few differences. When we put the new window into the opening using a replacement frame, you don't have the flush breakwater holding the frame in place. You and your helper have to hold the frame in place while we put a screw supremacy the top center to support the frame. Then, you can wind up your alteration since a argue for condition. All of the procedures on the inside will steward exactly the same, from hole plugs, to insulation, to trim and caulk. The frontage is different. You have to apply the trim that was part of its retrofit frame. Again, I lift the flat trim. Once again, you apply a bead of caulk to the hackneyed frame,then measure and cut the top and bottom polished pieces. Apply the adhesive part of the trim to the recording frame, and let the other part contact the stone of caulk. Trim all 4 sides, then caulk again location the supine meets the exterior material.

As you can see, undeniable really doesn't matter if the exterior of your home is brick, stone, siding, or stucco. You can install vinyl windows without having to damage the surrounding structure. We regard step by stride instructional videos for sale on its website at How To constitute WindowsVisit Original SourceHOME DESIGN SOFTWARE